| Brand Name: | YUHONG |
| Model Number: | N/A |
| MOQ: | 500kgs |
| Price: | To be discussed |
| Packaging Details: | Plywood case or Iron frame wooden case |
| Payment Terms: | L/C,T/T |
KL wound finned tubes for fired heaters are specially designed heat-transfer components used in industrial heating systems, process furnaces, and selected convection-section applications. Manufactured with an ASME SA179 seamless cold-drawn low-carbon steel base tube and mechanically wound KL-type fins, these tubes increase the external heat-transfer surface area and improve heat recovery from hot flue gases.
The KL finned tube is an enhanced version of the conventional L-footed fin tube. Before fin winding, the outside surface of the base tube is knurled. The fin strip is then helically wound around the tube, with its foot mechanically pressed into the corresponding knurled surface. This interlocking structure improves fin-to-tube contact and provides better resistance to thermal cycling than a conventional L-foot fin design.
Our KL wound finned tubes combine reliable base tube quality, consistent fin geometry, and customized manufacturing dimensions to meet the requirements of fired-heater manufacturers, EPC contractors, and industrial heat-transfer equipment suppliers.
Product name: KL Wound Finned Tubes for Fired Heaters
Base tube material: ASME SA179 / ASTM A179
Fin type: KL-type knurled-foot helical fin
Fin attachment: Mechanical winding and interlocking
Typical fin materials: Aluminum or copper, subject to operating conditions
Main applications: Fired-heater convection sections, industrial process heaters, air preheaters, and selected heat-recovery systems.
Important engineering consideration
KL finned tubes are generally used in relatively moderate-temperature service. Conventional aluminum KL fins are commonly limited to approximately 260°C maximum operating temperature, depending on the fin material, construction, and manufacturer. They are therefore not suitable for every fired-heater application, particularly high-temperature radiant sections. The actual flue-gas temperature, tube-metal temperature, corrosion environment, and design conditions must be checked before material selection.
Profins+1
Enhanced heat-transfer area: Helically wound fins increase the external surface area available for heat exchange.
Improved mechanical bonding: The knurled tube surface and matching fin foot create a mechanical interlock that improves contact between the fin and base tube.
Better thermal-cycle resistance: The KL configuration provides improved resistance to fin loosening during thermal cycling compared with conventional L-foot fin designs.
High-quality carbon steel base tube: ASME SA179 seamless tubing offers consistent mechanical properties and good fabrication characteristics for suitable heat-exchanger service.
Flexible fin materials: Aluminum and copper fin strips can be selected according to operating temperature and corrosion requirements.
Customized production: Tube dimensions, fin height, fin pitch, fin thickness, and un-finned end lengths can be manufactured according to customer drawings.
|
Application |
Main function |
|---|---|
|
Fired-heater convection sections |
Recovers heat from combustion gases |
|
Industrial process heaters |
Improves heat-transfer surface area |
|
Refinery heating systems |
Supports heat recovery in suitable heater configurations |
|
Petrochemical plants |
Used in selected process heat exchangers |
|
Air preheaters |
Improves heat exchange between hot and cold air streams |
|
Industrial waste-heat recovery |
Helps recover energy from exhaust gases |
Application note: KL finned tubes are particularly suitable where mechanical fin retention and moderate operating temperatures are important. For hotter fired-heater convection duties, embedded (G-type), extruded, or welded finned tubes may be more appropriate depending on the design.
The following table provides typical commercial manufacturing dimensions for KL wound finned tubes. These are indicative production ranges rather than dimensional requirements specified by ASME SA179.
|
Parameter |
Typical specification |
|---|---|
|
Base tube outside diameter |
19.05–76.2 mm |
|
Base tube wall thickness |
1.65–6.0 mm |
|
Tube length |
3,000–18,000 mm |
|
Fin height |
10–25 mm |
|
Fin thickness |
0.3–0.5 mm |
|
Fin pitch |
2.0–5.0 mm |
|
Fin type |
KL-type knurled-foot |
|
Fin arrangement |
Helically wound |
|
Fin material |
Aluminum 1060, copper, or specified alternative |
|
Base tube material |
ASME SA179 |
|
Fin attachment |
Mechanical interlocking |
|
Tube surface |
Knurled before fin winding |
|
Un-finned ends |
Customized according to drawings |
Customization options:
Different base tube diameters and wall thicknesses.
Customized fin height, pitch, and thickness.
Aluminum or copper fin strips.
Customized tube lengths and bare-end dimensions.
Special packaging and marking for export orders.
The ASME SA179 material specification covers seamless cold-drawn low-carbon steel heat-exchanger and condenser tubes with outside diameters from 3.2 mm to 76.2 mm. It does not specify KL fin dimensions or the mechanical winding process.
ASTM Store+1
ASME SA179 is a low-carbon steel specification designed for seamless cold-drawn heat-exchanger and condenser tubing. Its chemical composition provides good ductility, formability, and suitability for conventional heat-transfer equipment.
The following table shows the chemical composition requirements for ASTM A179/ASME SA179.
|
Element |
Chemical composition (wt.%) |
|---|---|
|
Carbon (C) |
0.06–0.18 |
|
Manganese (Mn) |
0.27–0.63 |
|
Phosphorus (P) |
≤ 0.035 |
|
Sulfur (S) |
≤ 0.035 |
ASTM Store+1
Material characteristics:
Carbon contributes to the strength and hardness of the steel.
Manganese improves strength and supports steelmaking quality.
Phosphorus is controlled to maintain appropriate ductility and toughness.
Sulfur is limited to reduce the risk of undesirable inclusions and associated fabrication problems.
The chemical composition requirements apply to the SA179 base tube. Aluminum or copper fin strips have separate material specifications and chemical requirements.
The following are the typical specified minimum mechanical properties and maximum hardness requirements for ASTM A179/ASME SA179 tubing.
|
Mechanical property |
Requirement |
|---|---|
|
Tensile strength |
≥ 325 MPa |
|
Yield strength |
≥ 180 MPa |
|
Elongation in 50.8 mm (2 in.) |
≥ 35% |
|
Rockwell hardness |
≤ 72 HRB |
tubemfg.com+1
These mechanical properties apply to the base tube, not the complete KL finned assembly. The mechanical retention of the fin should be evaluated separately using an agreed fin-bond or retention test.
Our KL wound finned tubes are manufactured through a controlled process to achieve consistent dimensions and reliable mechanical contact between the fin and base tube.
Step 1 – Raw material selection
Seamless ASME SA179 carbon steel tubes are selected according to the specified outside diameter, wall thickness, and length. Material certificates and heat numbers are verified.
Step 2 – Tube surface preparation
The base tube is cleaned and prepared to ensure a uniform surface before knurling.
Step 3 – Knurling process
A controlled knurling pattern is formed on the external surface of the base tube. This creates a mechanical profile designed to engage with the foot of the KL fin.
Step 4 – Fin strip preparation
Fin strips are prepared from the specified aluminum or copper material. Fin thickness, width, and surface condition are checked before winding.
Step 5 – KL fin winding
The fin strip is helically wound around the knurled tube. The fin foot is mechanically pressed into the corresponding knurled surface, creating an interlocking connection.
Step 6 – Dimensional correction
Fin pitch, height, alignment, and tube straightness are checked and adjusted to meet the approved technical drawings.
Step 7 – Final inspection and packaging
Finished products undergo dimensional, visual, and fin-retention inspections before protective packaging and delivery.
Quality inspection is essential to ensure that KL wound finned tubes meet the requirements of fired-heater and heat-exchanger manufacturers.
|
Inspection method |
Inspection purpose |
|---|---|
|
Mill Test Certificate review |
Verifies ASME SA179 material grade and traceability |
|
Chemical composition analysis |
Confirms carbon, manganese, phosphorus, and sulfur limits |
|
Tensile testing |
Verifies tensile strength, yield strength, and elongation |
|
Hardness testing |
Checks base tube hardness |
|
Dimensional inspection |
Measures tube OD, wall thickness, length, fin height, and pitch |
|
Knurling inspection |
Checks the consistency and geometry of the knurled tube surface |
|
Visual inspection |
Identifies surface defects, damaged fins, and irregular winding |
|
Fin retention test |
Evaluates the mechanical bonding strength between fin and base tube |
|
Flattening test |
Evaluates tube ductility and resistance to deformation |
|
Flaring test |
Evaluates tube material ductility |
|
Hydrostatic testing |
Checks pressure integrity of the base tube when required |
|
Eddy current testing |
Detects relevant tube-wall discontinuities using a suitable procedure |
|
Final inspection |
Confirms dimensions, surface condition, marking, and packaging |
Quality assurance note: ASTM A179/ASME SA179 requires specified material and mechanical testing, including hardness, flattening, flaring, and hydrostatic testing, with applicable general requirements. Additional fin-retention tests should be agreed upon separately because the standard does not define KL fin attachment acceptance criteria.
ASTM Store+1
Improved thermal contact: The knurled interlocking structure provides better mechanical contact between the fin foot and base tube.
Greater fin stability: KL construction offers improved resistance to fin movement during thermal cycling compared with conventional L-foot designs.
Increased heat-transfer surface: Helically wound fins provide a larger external surface for heat exchange.
Flexible material combinations: Aluminum and copper fins can be selected to suit compatible operating conditions.
Efficient heat recovery: Properly designed finned tube banks can improve convection-section heat recovery.
Customized engineering: Fin dimensions and tube configurations can be tailored to individual fired-heater designs.
To protect the fin structure and base tube during transportation, our KL wound finned tubes can be supplied with:
Protective end caps to prevent contamination.
Bundled packaging with suitable supports.
Protective wrapping to minimize moisture exposure.
Wooden cases or export-standard packaging.
Clear product identification, including material grade, dimensions, and quantity.
Mill Test Certificates and agreed inspection reports can be provided with the shipment.
For quotation and technical evaluation, please provide the following information:
|
Required information |
Specification |
|---|---|
|
Product |
KL wound finned tubes |
|
Application |
Fired heater |
|
Base tube standard |
ASME SA179 |
|
Base tube material |
Seamless low-carbon steel |
|
Tube outside diameter |
As per drawing |
|
Wall thickness |
As per drawing |
|
Tube length |
As per project requirements |
|
Fin material |
Aluminum / copper |
|
Fin height |
As per design |
|
Fin thickness |
As per design |
|
Fin pitch |
As per design |
|
Bare-end length |
As per drawing |
|
Quantity |
As per purchase order |
|
Inspection requirements |
As per project specification |
We welcome inquiries from fired-heater manufacturers, refinery engineering companies, petrochemical plants, EPC contractors, and industrial heat-exchanger suppliers worldwide.