logo
banner

news details

Home > News >

Company news about Studded Tube Processing Tips: Welding Parameters, Tolerances and Surface Treatment

Events
Contact Us
Sales Dept.
+86-574-88013900
Contact Now

Studded Tube Processing Tips: Welding Parameters, Tolerances and Surface Treatment

2026-11-16

Studded tube performance is set at the processing stage, not at the design stage. Two tubes with the same stud pattern behave differently in service if penetration, spacing or surface coating is not controlled. What decides whether it delivers its rated duty: welding current, stamping pressure, tolerance, surface treatment and pressure testing.

TIG Welding: Current Range and Penetration Control

For stud attachment by TIG welding, the current is normally held in the 80–120 A range. The objective is full penetration at the stud root without burn-through on the tube wall.

  • Too low: a lack of fusion — a "cold" weld that passes a visual check and fails under thermal cycling.
  • Too high: a through-wall defect, or a heat-affected zone wider than the qualified procedure allows.

The range is not universal: it is adjusted for stud diameter, wall thickness and base material, and the qualified procedure should state current, travel speed and shielding gas for each combination. Visual check alone does not confirm penetration; bend or pull tests on sampled studs are the verification step.

Resistance Welding or TIG: Which Route Applies

Both routes attach the stud to the tube wall; they differ in how heat is delivered. Resistance welding passes current and pressure through the stud in a short cycle, which suits high-volume arrays where the pattern must repeat exactly. TIG welding melts the joint under shielding gas, which suits thicker studs, alloy and stainless base tubes, and shorter runs where the procedure is written per combination. Both routes run in our workshop. Resistance welding is our standard production route for dense stud arrays, with PLC control of feed, indexing and welding parameters. TIG is used for thick studs, alloy and stainless base tubes, and shorter runs where the procedure is written per combination. The tolerances and inspection steps below apply to either.

Stamping Pressure for Thin-Wall Tube

For integrally formed studded tubes on thin-wall base tube, stamping pressure is set against the material and the wall thickness. Carbon steel typically needs 10–15% higher pressure than stainless at the same wall thickness, because the two flow differently under the forming load. One pressure for both risks under-forming on carbon steel, or over-forming and wall thinning on stainless.

Tolerance on Stud Spacing and Height

The pattern is only as good as its dimensional control. Two tolerances matter for heat transfer uniformity:

Parameter Limit If exceeded
Stud spacing deviation ±0.5 mm Lower stud density and higher gas velocity locally: less effective area, uneven fouling
Stud height error ±0.3 mm Stud height variation changes the local fin efficiency and the gas lane between studs; a few tall studs can shield the surrounding surface and trap deposit

Not cosmetic: they decide whether the array performs as a uniform extended surface or as a set of local hot and cold spots.

Surface Treatment for High-Temperature and Corrosive Service

Surface treatment is selected against the service environment:

Service Treatment Acceptance
High temperature High-temperature-resistant coating, typically 0.1–0.2 mm thick, protecting the base metal from oxidation and scaling Coating thickness against specification
Corrosive Anti-corrosion plating or coating Adhesion by cross-cut (cross-hatch) test — a coating that looks continuous but fails the test will not protect the surface

The coating is not a substitute for material selection: it extends the life of the chosen alloy, it does not turn carbon steel into stainless.

Pressure Testing Before Release

After processing, each tube is hydrostatically tested at 1.5 times the working pressure, held 30 minutes, no leakage permitted — confirming the pressure integrity of the base tube after stud welding and surface treatment.

In our production, the test record is traceable to the tube heat number and the batch, so a query on one bundle traces back to the parameters that produced it.

Frequently Asked Questions
What TIG welding current is used for studded tubes?

Normally 80–120 A, adjusted for stud diameter, wall thickness and base material. The qualified procedure should state current and travel speed per combination, and penetration is verified by bend or pull tests on sampled studs.

Why is stamping pressure higher for carbon steel than stainless steel?

At the same wall thickness, carbon steel typically needs 10–15% more, because the two materials flow differently under the forming load. One setting risks under-forming or wall thinning.

What tolerances apply to stud spacing and height?

Spacing deviation within ±0.5 mm and height error within ±0.3 mm. These control the uniformity of the extended surface and the gas flow path, and are checked at dimensional inspection.

How is the surface coating verified?

For high-temperature service, thickness is checked against the 0.1–0.2 mm spec. For anti-corrosion coatings, adhesion is verified by a cross-cut test; a coating that fails is rejected regardless of appearance.

Studded tube with uniform stud arrangement ready for processing review

Close-up of a welded stud joint on a studded tube for parameter verification

banner
news details
Home > News >

Company news about-Studded Tube Processing Tips: Welding Parameters, Tolerances and Surface Treatment

Studded Tube Processing Tips: Welding Parameters, Tolerances and Surface Treatment

2026-11-16

Studded tube performance is set at the processing stage, not at the design stage. Two tubes with the same stud pattern behave differently in service if penetration, spacing or surface coating is not controlled. What decides whether it delivers its rated duty: welding current, stamping pressure, tolerance, surface treatment and pressure testing.

TIG Welding: Current Range and Penetration Control

For stud attachment by TIG welding, the current is normally held in the 80–120 A range. The objective is full penetration at the stud root without burn-through on the tube wall.

  • Too low: a lack of fusion — a "cold" weld that passes a visual check and fails under thermal cycling.
  • Too high: a through-wall defect, or a heat-affected zone wider than the qualified procedure allows.

The range is not universal: it is adjusted for stud diameter, wall thickness and base material, and the qualified procedure should state current, travel speed and shielding gas for each combination. Visual check alone does not confirm penetration; bend or pull tests on sampled studs are the verification step.

Resistance Welding or TIG: Which Route Applies

Both routes attach the stud to the tube wall; they differ in how heat is delivered. Resistance welding passes current and pressure through the stud in a short cycle, which suits high-volume arrays where the pattern must repeat exactly. TIG welding melts the joint under shielding gas, which suits thicker studs, alloy and stainless base tubes, and shorter runs where the procedure is written per combination. Both routes run in our workshop. Resistance welding is our standard production route for dense stud arrays, with PLC control of feed, indexing and welding parameters. TIG is used for thick studs, alloy and stainless base tubes, and shorter runs where the procedure is written per combination. The tolerances and inspection steps below apply to either.

Stamping Pressure for Thin-Wall Tube

For integrally formed studded tubes on thin-wall base tube, stamping pressure is set against the material and the wall thickness. Carbon steel typically needs 10–15% higher pressure than stainless at the same wall thickness, because the two flow differently under the forming load. One pressure for both risks under-forming on carbon steel, or over-forming and wall thinning on stainless.

Tolerance on Stud Spacing and Height

The pattern is only as good as its dimensional control. Two tolerances matter for heat transfer uniformity:

Parameter Limit If exceeded
Stud spacing deviation ±0.5 mm Lower stud density and higher gas velocity locally: less effective area, uneven fouling
Stud height error ±0.3 mm Stud height variation changes the local fin efficiency and the gas lane between studs; a few tall studs can shield the surrounding surface and trap deposit

Not cosmetic: they decide whether the array performs as a uniform extended surface or as a set of local hot and cold spots.

Surface Treatment for High-Temperature and Corrosive Service

Surface treatment is selected against the service environment:

Service Treatment Acceptance
High temperature High-temperature-resistant coating, typically 0.1–0.2 mm thick, protecting the base metal from oxidation and scaling Coating thickness against specification
Corrosive Anti-corrosion plating or coating Adhesion by cross-cut (cross-hatch) test — a coating that looks continuous but fails the test will not protect the surface

The coating is not a substitute for material selection: it extends the life of the chosen alloy, it does not turn carbon steel into stainless.

Pressure Testing Before Release

After processing, each tube is hydrostatically tested at 1.5 times the working pressure, held 30 minutes, no leakage permitted — confirming the pressure integrity of the base tube after stud welding and surface treatment.

In our production, the test record is traceable to the tube heat number and the batch, so a query on one bundle traces back to the parameters that produced it.

Frequently Asked Questions
What TIG welding current is used for studded tubes?

Normally 80–120 A, adjusted for stud diameter, wall thickness and base material. The qualified procedure should state current and travel speed per combination, and penetration is verified by bend or pull tests on sampled studs.

Why is stamping pressure higher for carbon steel than stainless steel?

At the same wall thickness, carbon steel typically needs 10–15% more, because the two materials flow differently under the forming load. One setting risks under-forming or wall thinning.

What tolerances apply to stud spacing and height?

Spacing deviation within ±0.5 mm and height error within ±0.3 mm. These control the uniformity of the extended surface and the gas flow path, and are checked at dimensional inspection.

How is the surface coating verified?

For high-temperature service, thickness is checked against the 0.1–0.2 mm spec. For anti-corrosion coatings, adhesion is verified by a cross-cut test; a coating that fails is rejected regardless of appearance.

Studded tube with uniform stud arrangement ready for processing review

Close-up of a welded stud joint on a studded tube for parameter verification